Autotriggers for sale

[Koa]

These Sniper/Cocker pump Autotrigger kits Fits 45 Sliders and DYE pivots.


This Autotrigger does NOT fit CCM frames at all!!!!!



Autotrigger $50
Fits OLD WGP Stock Pivot Frames 5 left circa 1980-1990
45 frame ATs Sold out!!! it will take a while, BLAME THUMPER

$10 Modding Pump Rod
send it in to get drilled & tapped



Trigger Plate Modification:
$20 to Mod a Slider trigger plate
$50 to mod a ANS
$80 AKA trigger plate

I use Titanium Putty from Devcon, it does wear off a little but i have had the same slider with Ti Putty for 2 years and haven't had to replace the putty yet, also it slight wears the cam polishing it like how 600 grit paper would....i have been using a cam 10 years old (using the putty plate for 2 years) and its still ok




modding your own trigger isn't that hard The Autotrigger Strikes Back!!! thread has information, and i would much prefer you to do it.


What you need to install an autotrigger

1) Slider plate with flat spot for cam, or a Dye/32 degrees pivot
2) Pump rod with hole drilled into it
3) Trigger frame with safety hole
4) And most importantly....the ability to think.....no stupid people please

if you own a pump rod you could either drill and tap the hole for a 4-40 screw, or send it in to me for $10


if you have a Dye Pivot frame(or any knockoff) the AT cam Drops right in with no mods to the frame, i hate all who have them i am jealous.


if you Own a Slider frame trigger plate you will need to mod it like the pic above or get it modded by me for $10, Best to DIY!!! its really easy.....just need TI Putty, or know how to weld, or know people who can do it for you.

just make sure the surface is flat like in the pic...and it clears the Safety hole and youll be ok





HOW TO ORDER!!!
1) Figure out what frame you have (45 slider, Dye/32 degrees Pivot, Stock Sniper2 pivot(non 45 frames) ONLY!!!!)
2) Decide if you need your pump rod modded
3) Send to me and wait


DISCLAIMER, these are not drop in and require some tunning/adjustment.  But as MCB members you should feel that this is an integral part of paintball, and that small amount of personal tunning/adjustment to your marker makes it better than any other marker out there
well....thats how i feel


for questions please email koaisaok@gmail.com
or IM me

[mayor]

 Hey, im really interested in this. So would $75 cover the kit, and tapping of the pump arm? (I have a WGP slider)

[Koa]

Hey, im really interested in this. So would $75 cover the kit, and tapping of the pump arm? (I have a WGP slider)

These Sniper/Cocker pump Autotrigger kits Fits 45 Sliders, DYE pivots, old stock WGP frames and WGP 45 Slider frames found on the Nightcast and Karni pumps.
Autotrigger kit
Everything you need installed and ready to play!!!!
slider users supply own trigger plate for modding
$75

[Koa]

i guess it wasnt clear, so i tried to clarify.....try read now

[Koa]

ok well it seems some frames have safety holes MUCH lower than what i used to measure how long the levers are, so in order for the levers to work on more frames i need to mill the slot longer...and the cam screw hole longer as well

the result is GHETTO fabness, but it works fine


so im blowing out these GHETTO Levers for only 10 bucks SELF INSTALLS ONLY

if your sending in your gun or parts for fitting.....then its normal price

[Koa]

OK i got some ATs for old school WGP Pivots and sliders 50 each