Autotriggers for sale

[Koa]

DISCLAIMER, these are not drop in and require some tuning/adjustment.

To Order email me at koaisaok@gmail.com

Frames that my Autotrigger Fits:
Slider frames:
   Benchmark, Belsales, Dye, KAPP, Freeflow, ANS, and more

Pivot/Hinge frames:
   DYE, 32 degrees


Frames that my Autotrigger Does NOT fit:
Slider frames:
   WGP & Powerlyte both require modding

Pivot/Hinge frames:
   Eclipse, Kapp Reflex, CCM Frames




Autotrigger $50


Modded Stock WGP Trigger Plates $20 each
I have a small amount of them, i premodded them to make installation MUCH easier


Trigger Plate Modification:
based on excess metal in plate and plate hardness
$10 to Mod a stock Slider trigger plate
$20 to mod a ANS trigger plate
$50 AKA trigger plate
turnaround is about 3 days




Drill & Tap Pump Rod for Lever Screw $10
turnaround is 1 day





FAQ

What pump kit mods are needed for an autotrigger?
A Pump rod with 4-40 tapped hole drilled into it.

What MODs do DYE Pivot frames need for an autotrigger?
NONE!

What MODs Slider frame need for an autotrigger?
just make sure the surface is flat like in the pic...and it clears the Safety hole and you'll be OK






Autotrigger Instructions click me


I use Titanium Putty from Devcon, it does wear off a little but i have had the same slider with Ti Putty for 2 years and haven't had to replace the putty yet, also it slight wears the cam polishing it like how 600 grit paper would....i have been using a cam 10 years old (using the putty plate for 2 years) and its still ok


modding your own trigger isn't that hard The Autotrigger Strikes Back!!! thread has information, and i would much prefer you to do it.




HOW TO ORDER!!!
1) Figure out what frame you have (45 slider, Dye/32 degrees Pivot, Stock Sniper2 pivot(non 45 frames) ONLY!!!!)
2) Decide if you need your pump rod modded
3) email me your order to koaisaok@gmail.com
4) if needed Send necessary parts for Modding


DISCLAIMER, these are not drop in and require some tuning/adjustment.


To Order email me at koaisaok@gmail.com


you can install them on autocockers, Space Time Paradox Safe

http://www.youtube.com/watch?v=lIiyvTGiOqA

[mayor]

 Hey, im really interested in this. So would $75 cover the kit, and tapping of the pump arm? (I have a WGP slider)

[Koa]

Hey, im really interested in this. So would $75 cover the kit, and tapping of the pump arm? (I have a WGP slider)

These Sniper/Cocker pump Autotrigger kits Fits 45 Sliders, DYE pivots, old stock WGP frames and WGP 45 Slider frames found on the Nightcast and Karni pumps.
Autotrigger kit
Everything you need installed and ready to play!!!!
slider users supply own trigger plate for modding
$75

[Koa]

i guess it wasnt clear, so i tried to clarify.....try read now

[Koa]

ok well it seems some frames have safety holes MUCH lower than what i used to measure how long the levers are, so in order for the levers to work on more frames i need to mill the slot longer...and the cam screw hole longer as well

the result is GHETTO fabness, but it works fine


so im blowing out these GHETTO Levers for only 10 bucks SELF INSTALLS ONLY

if your sending in your gun or parts for fitting.....then its normal price

[Koa]

OK i got some ATs for old school WGP Pivots and sliders 50 each

[Koa]

i got 45 frame, Sheridan & Old Cocker ATs available

[Koa]

Only 2 Complete kits Left!

Cams still available $25

[jwongie]

hey koa its jordan from poi dogz got a sniper that i wanna put an autotrigger on lmk when ur available??

[Koa]

i am now

[jwongie]

hmmm can i meet u some time tomorro? the plate on my frame is already modded i jus need my rod drilled and tapped and the ac

[Koa]

ok what frame you got?

[jwongie]

i got a wgp slider. . .um im not sure where ill be this morning but if i can swing by ur shop/house and you can install the at then giv me a call 220-8748

[jwongie]

sorry i was allot busier yesterday than i thought i would be and i hav school and work during the week but ill giv u a call on saturday. . .where u located?

[Koa]

Manoa/Makiki near punahou